Hello!

I've decided that you guys are awesome, and are probably the grandfathers of all knowledge, so here's hoping that you can help me.

I have a dead Nokia 6086, and I tried to use Phoenix to revive it. Everything works smoothly until the very end. When the program attempts to make the final connection with the phone, it times out.

I used the latest all-in-one release from Phoenix Slayer. The installation is 100% clean. I even reformatted my harddrive so that I could ensure everything was pristine before I started.

The only possible problem I could think of is that this phone is RM-260, but I could not find the flash files for RM-260 anywhere, so I used RM-188. I was told from various sources that this would work. Update: I finally found RM-260 and used it. The exact same error occurs. Update 2: I noticed that when it gets to "Rebooting to Normal Mode" the audible tone that means "usb disconnected" goes off. When I push the power button on the phone the tone for "usb connected" goes off, but is closely followed by the disconnect tone.

Here is the complete log for your collective pleasure:

Flashing started
Creating product data items list
Product data items list created
Backup not required
Flashing phone
Initializing
Loading image files...
Waiting for USB device. Press phone's power button (if you start from dead terminal)
ROM Boot Drivers loaded. Creating RAW connection
Connecting to device...
Connection opened
Connection opened to BootCode successfully
First wait command succeeded.
First wait command failed. Preparing for bootrom waiting loop ...
Flashing Secondary boot code: 14464 Bytes
Secondary boot loaded
Skipping USB handshake...
Flashing Update Server Data: 243008 Bytes
Flashing PASUB TOC Data: 27904 Bytes
Update server loaded
Waiting for Update Server to boot...
Closing connection
Connecting to device...
Connection opened
Asic CMT: Verifying communication to device...
Initializing Update Server....
Asic CMT: Verifying communication to device...
Loading image files...
Loading image files...
Phone page size 128 differs from file.
Creating 128k file from rm188__05.03.image_a...
Asic CMT: Selecting programming blocks...
Warning: PAPUBKEY already selected
Flashing SingleAsic device...
Asic CMT: Erasing rm188__05.03.mcusw.bin
Asic CMT: Erasing area 1...
Asic CMT: Erasing area 2...
Asic CMT: Erasing rm188__05.03.ppm_a
Asic CMT: Erasing area 1...
Asic CMT: Erasing rm188__05.03.image_a_128
Asic CMT: Erasing area 1...
Asic CMT: Erasing area 1...
Asic CMT: Programming rm188__05.03.mcusw.bin
Asic CMT: Programming 0%
Asic CMT: Programming 2%
Asic CMT: Programming 4%
Asic CMT: Programming 6%
Asic CMT: Programming 8%
Asic CMT: Programming 10%
Asic CMT: Programming 12%
Asic CMT: Programming 14%
Asic CMT: Programming 16%
Asic CMT: Programming 18%
Asic CMT: Programming 20%
Asic CMT: Programming 22%
Asic CMT: Programming 24%
Asic CMT: Programming 26%
Asic CMT: Programming 28%
Asic CMT: Programming 30%
Asic CMT: Programming 32%
Asic CMT: Programming 34%
Asic CMT: Programming 36%
Asic CMT: Programming 38%
Asic CMT: Programming 40%
Asic CMT: Programming 42%
Asic CMT: Programming 44%
Asic CMT: Programming 46%
Asic CMT: Programming 48%
Asic CMT: Programming 50%
Asic CMT: Programming 52%
Asic CMT: Programming 54%
Asic CMT: Programming 56%
Asic CMT: Programming 58%
Asic CMT: Programming 60%
Asic CMT: Programming 62%
Asic CMT: Programming 64%
Asic CMT: Programming 66%
Asic CMT: Programming 68%
Asic CMT: Programming 70%
Asic CMT: Programming rm188__05.03.ppm_a
Asic CMT: Programming 72%
Asic CMT: Programming 74%
Asic CMT: Programming 76%
Asic CMT: Programming 78%
Asic CMT: Programming 80%
Asic CMT: Programming 82%
Asic CMT: Programming rm188__05.03.image_a_128
Asic CMT: Programming 84%
Asic CMT: Programming 86%
Asic CMT: Programming 88%
Asic CMT: Programming 90%
Asic CMT: Programming 92%
Asic CMT: Programming 94%
Asic CMT: Programming 96%
Asic CMT: Programming 98%
Finished Flashing
Rebooting to Normal Mode
Asic CMT: Verifying communication to device...
Waiting for communication response: 25
Waiting for communication response: 24
Waiting for communication response: 23
Waiting for communication response: 22
Waiting for communication response: 21
Waiting for communication response: 20
Waiting for communication response: 19
Waiting for communication response: 18
Waiting for communication response: 17
Waiting for communication response: 16
Waiting for communication response: 15
Waiting for communication response: 14
Waiting for communication response: 13
Waiting for communication response: 12
Waiting for communication response: 11
Waiting for communication response: 10
Waiting for communication response: 9
Waiting for communication response: 8
Waiting for communication response: 7
Waiting for communication response: 6
Waiting for communication response: 5
Waiting for communication response: 4
Waiting for communication response: 3
Waiting for communication response: 2
Waiting for communication response: 1
Error 0x84009427 communicating to phone. Unable to verify comm.
Warning: Unable to communicate to product after flashing
All operations completed
Product flashing failed.

Thanks in advance for any advice you can offer. This has to be the best, most active and helpful forums I have ever encountered.

Kenson

where you able to get this thing to flash, i have the same issue. If you were able to flash this. I was wondering you could give me the solution as well.
thanks

hi all. can anyone tell me how to flash DEAD n73-5 (rm-132). actually i 1st change the phone product code, then i updated it to latest firmware of rm-133. but i don't liked the latest firmware language file so i was trying it install my previous firmware. what i do, i just take the image file of latest firmware ( i.e FPSX file) and the language file of previous firmware.
( i.e V12 file). but during flashing process Phoenix interrupted and said that installing firmware is older than the installed firmware and when i restarted my phone it is dead. it shows the start up NOKIA logo then it just restarted again and again. plz help me, i m scared to take it to nokia care bcoz i have heard that changing the product code will void my phone's warranty. what should i do?

I have the same problem with my 5610. I hope someone will help. The flashing process of mine is below.


Flashing started
Creating product data items list
Product data items list created
Backup not required
KeepProductInFlashModeAfterFlash is supported only for FPS-X devices. Ignoring the flag
Flashing phone
Initializing
Loading image files...
Opening RAW connection...
RAW connection successfully opened!
Waiting for USB device...
--- Press phone's power button! ---
Connection opened to BootCode successfully
First wait command succeeded.
Flashing Secondary boot code: 14592 Bytes
Secondary boot loaded
Skipping USB handshake...
Flashing Update Server Data: 290624 Bytes
Flashing PASUB TOC Data: 59584 Bytes
Update server loaded
Waiting for Update Server to boot...
Restoring normal connection...
Asic CMT: Verifying communication to device...
Initializing Update Server....
Asic CMT: Verifying communication to device...
Loading image files...
Loading image files...
Asic CMT: Selecting programming blocks...
Flashing SingleAsic device...
Asic CMT: Erasing rm242__06.60.mcusw
Asic CMT: Erasing area 1...
Asic CMT: Erasing area 2...
Asic CMT: Erasing area 3...
Asic CMT: Erasing area 4...
Asic CMT: Erasing area 5...
Asic CMT: Erasing rm242__06.60.ppm_i
Asic CMT: Erasing area 1...
Asic CMT: Erasing rm242__06.60_ISM_002.image_pink_i_cis_no_yahoo
Asic CMT: Erasing area 1...
Asic CMT: Erasing area 2...
Asic CMT: Programming rm242__06.60.mcusw
Asic CMT: Programming 0%
Asic CMT: Programming 2%
Asic CMT: Programming 4%
Asic CMT: Programming 6%
Asic CMT: Programming 8%
Asic CMT: Programming 10%
Asic CMT: Programming 12%
Asic CMT: Programming 14%
Asic CMT: Programming 16%
Asic CMT: Programming 18%
Asic CMT: Programming 20%
Asic CMT: Programming 22%
Asic CMT: Programming 24%
Asic CMT: Programming 26%
Asic CMT: Programming 28%
Asic CMT: Programming 30%
Asic CMT: Programming 32%
Asic CMT: Programming 34%
Asic CMT: Programming 36%
Asic CMT: Programming 38%
Asic CMT: Programming 40%
Asic CMT: Programming 42%
Asic CMT: Programming 44%
Asic CMT: Programming 46%
Asic CMT: Programming 48%
Asic CMT: Programming rm242__06.60.ppm_i
Asic CMT: Programming 50%
Asic CMT: Programming 52%
Asic CMT: Programming 54%
Asic CMT: Programming 56%
Asic CMT: Programming 58%
Asic CMT: Programming 60%
Asic CMT: Programming 62%
Asic CMT: Programming rm242__06.60_ISM_002.image_pink_i_cis_no_yahoo
Asic CMT: Programming 64%
Asic CMT: Programming 66%
Asic CMT: Programming 68%
Asic CMT: Programming 70%
Asic CMT: Programming 72%
Asic CMT: Programming 74%
Asic CMT: Programming 76%
Asic CMT: Programming 78%
Asic CMT: Programming 80%
Asic CMT: Programming 82%
Asic CMT: Programming 84%
Asic CMT: Programming 86%
Asic CMT: Programming 88%
Asic CMT: Programming 90%
Asic CMT: Programming 92%
Asic CMT: Programming 94%
Asic CMT: Programming 96%
Asic CMT: Programming 98%
Finished Flashing
Rebooting to Normal Mode
Asic CMT: Verifying communication to device...
Waiting for communication response: 25
Waiting for communication response: 24
Waiting for communication response: 23
Waiting for communication response: 22
Waiting for communication response: 21
Waiting for communication response: 20
Waiting for communication response: 19
Waiting for communication response: 18
Waiting for communication response: 17
Waiting for communication response: 16
Waiting for communication response: 15
Waiting for communication response: 14
Waiting for communication response: 13
Waiting for communication response: 12
Waiting for communication response: 11
Waiting for communication response: 10
Waiting for communication response: 9
Waiting for communication response: 8
Waiting for communication response: 7
Waiting for communication response: 6
Waiting for communication response: 5
Waiting for communication response: 4
Waiting for communication response: 3
Waiting for communication response: 2
Waiting for communication response: 1
Error 0x84009427 communicating to phone. Unable to verify comm.
Warning: Unable to communicate to product after flashing
All operations completed
Product flashing failed.

Did someone find a solution? I have the same prob and really need your help..thanx!

Are there still no solution on this matter? Now my 6500s become a dead phone and phoenix not even can detect my phone via usb cable.Please if anybody have the solution to post it here.I really need the solution to make my 6500s work again..

I suggest you guys to pm any box supporter to get solution or find the solution by goggling it...