Installation SE_Navcore.8.410.1218.rev1.2 for GO910 (voices of original)
Read here :
http://www.ipmart-forum.com/showpost.php?p=2599747&postcount=101

Installation SE_Navcore.8.410.1218 rev1.1 for GO910 (voices of original)
Sorry for my English:sorry:

Download Jdownloader :
http://www.anonym.to/?http://jdownloader.org/download/index
For download with JDownloader, read (example) :
http://www.ipmart-forum.com/showpost.php?p=2566284&postcount=15
(By following the example, you have the folder ASR => 20450368 bytes)

- Read :
http://www.ipmart-forum.com/showpost.php?p=2563628&postcount=1
- You should have the folder : ASR => 20450368 bytes
- Download :
http://www.anonym.to/?http://rapidshare.com/files/207488048/SE_Navcore.8.410.1218.Basicpack.rar
Extract the folder : SE_Navcore.8.410.1218.Basicpack
- Download :
http://www.anonym.to/?http://rapidshare.com/files/207493352/SE_ttsystem.8.410.1218.rar
Extract the folder : SE_ttsystem.8.410.1218
- Download :
http://www.ipmart-forum.com/attachment.php?attachmentid=448965&d=1227044472
Extract the folder LoquendoTTS
- Download :
http://www.ipmart-forum.com/attachment.php?attachmentid=450399&d=1227432495
Extract the folder suspend
- Download the map you want to use :
For map : Western_and_Central_ Europe 825.2157 or other countries
For map : North_America 825.2157
Maps located in the thread below (in the last pages) :
http://www.ipmart-forum.com/showthread.php?t=337584
For map : Australia 815.2086
Map located in the thread below (in the last pages) :
http://www.ipmart-forum.com/showthread.php?t=337608
Extract the map
- To activate the map, read and download : Easyusetools for Keygen Mapcheck Metacheck ttsystempatcher
http://www.ipmart-forum.com/showpost.php?p=2086254&postcount=58
Extract the folder Easyusetools_for Keygen_Mapcheck_Metacheck_ttsystempatcher

Installation :
1- Save the contents of your GO910 in a safe place on your hard drive
2- Clear all the contents of your GO910
3- Install the folder ASR to the root of your GO910
4- Install the folder LoquendoTTS (downloaded) to the root of your GO910
- From the saved copy of your TomTom : in the folder LoquendoTTS make a copy folders Dutch, EnglishGb, EnglishUs, French, German, Italian, PortuguesePt, Spanish then paste them inside the folder LoquendoTTS (previously installed) on your GO910. Close the folder LoquendoTTS
For those who do not have these folders download the voices :
http://www.ipmart-forum.com/showthread.php?t=170022
5- Open the folder : SE_Navcore.8.410.1218.Basicpack (downloaded)
- Install SE_Navcore.8.410.1218.Basicpack contents of the folder to the root of your GO910 later :
- delete the folders Navcore.8.410.1218@ tomtom.com, Outsourced.8410 and the file readmenot.txt
- unzip the folder switchfiles.zip, open the folder swichfiles, open the folder Config, copy the files setconfig.txt, version.txt and paste them in the root of your GO910
- open the file setconfig.txt, keep only runclean and changedtext:TomTom GO 940 LIVE (delete all other files), delete 40 LIVE, write for example : 10 with your name, close the file setconfig.txt
- delete the folders switchfiles.zip and switchfiles
6- Open the folder : SE_ttsystem.8.410.1218 (downloaded)
- Copy the file ttsystem and paste it in the root of your GO910
7- Open the folder suspend (downloaded), copy the file suspend.ogg and paste it in the root of your GO910
For those who do not have antenna RDS/TMC : Make a copy of the file suspend.ogg and paste it in the root of your GO910
Rename the file : Copy of suspend.ogg => TTPnPD
Open the file TTPnPD (with Notpad), delete the contents, close the file TTPnPD
8- Add the folders and files you want from your backup :
- Folders : art, audiobooks, contacts, ephem, helpme, itn, mp3, photos, raster, sounds, zip ...
- Files : antitheftw.bmp, autorun.inf, splashw.bmp, suspendw.bmp, tomtom.ico ...
9- Install the map :
- Install the folder(s) of your map(s) (downloaded) to the root of your GO910
- Open the folder : Easyusetools_for Keygen_Mapcheck_Metacheck_ttsystempatcher (downloaded)
Double click on : Easyusetools_for Keygen_Mapcheck_Metacheck_ttsystempatcher
Double click on : RunMeforAllAutomatic.cmd
Select : 1 or follow the onscreen instructions
10- Disconnect the GO910, let it reboot (select in Windows “Safe disconnect”, disconnect GO910 from the computer (take it from a cradle)) Wait the message : Create ttgo.bak (about 1 minute)
11- Making various settings
12- Switch off and then turn on the GO910 to properly save the configuration

Caution : when you switch off the GO910 and put it on the cradle, after 45 – 50 seconds it automatically restart and connect to your computer

For TTHome2 : I use the old method (I do not handle my GO910 with TTHome)
With XP :
Open folder : SE_Navcore.8.410.1218.Basicpack (downloaded), open the folder Navcore.8.410.1218@ tomtom .com, copy the file 8-410-1218-1.dll
In C:\Documents and Settings\ ????????\Application Data\TomTom\HOME\Profiles\xxxxxxxx.default\extensi ons\Navcore.7.903.9183@tomtom.com (or other), I paste file 8-410-1218-1.dll, I note the file name .dll (7-903-9183-1.dll (or other)), I delete the file : 7-903-9183-1.dll (or other), and I rename file 8-410-1218-1.dll : 7-903-9183-1.dll (or other)
With Vista : C:\Users\????????\AppData\Roaming\TomTom\HOME\Prof iles\xxxxxxxx.default\extension\Navcore.7.........

:thanks::thanks::thanks:
Bonne route et merci TTuser:urtheman::urtheman::urtheman:

grard31

So, are you more satisfied with this Nav than 8.204 in your 910? What are pros..I mean feelings from your side?
Anyway, thanks for your work & reps go to ya.

oops...double posted/ipmart delay...sorry

So, are you more satisfied with this Nav than 8.204 in your 910? What are pros..I mean feelings from your side?
Anyway, thanks for your work & reps go to ya.
Thank you ghost2

My opinion,
Without the file Outsourced, it has the same free memory available.
I think that at the end of development, it will be substantially higher navcore 8204.

grard31

Please, remote control works? (go910)

free memory within the tomtom device does not say anything about how much free memory is really available. Anyway it is linux and linux tries to stuff the memory as full as possible and that's the way any operation system should do it: free memory is useless!

Neta76

Old remote : no
Remote bluetooth : yes

vincentn1981

Why your TOMTOM ONE could not use LoquendoTTS with navcore 8.204 ...

grard31

@grard31 good question, what do you think? I have the idea you want to relate this to the amount of free ram available indicated within the tomtom menu, however 8.410 can with a specific switch support Loquendo on a TT One, so therefore I conclude it is not a free ram problem. Anyway the free ram indicated within TomTom does not say anything.

Anybody get GPRS traffic going on this?

Anybody get GPRS traffic going on this?
For GPRS read here :

http://www.ipmart-forum.com/showpost.php?p=2564314&postcount=53

but not for GO910

grard31

Hi Grard,

Excellent working dump!

One question, maybe you have a solution: When I put my GO910 on the window mount in the car it keeps searching for TMC signal. Very annoying.
Maybe you or somebody else know how to shut down TMC/RDSfunction?
Thanks in advance, gr Tjilitjap :good2:

Hi Grard,

Excellent working dump!

One question, maybe you have a solution: When I put my GO910 on the window mount in the car it keeps searching for TMC signal. Very annoying.
Maybe you or somebody else know how to shut down TMC/RDSfunction?
Thanks in advance, gr Tjilitjap :good2:
tjilitjap,

Switch off and then turn on your GO910, when it is on the window mount...

grard31

Originally Posted by oac
Problem solved: Put an emty file on the root directory of the sdcard name it "TTPnPD" -> tmc is off

I need to be more carefull reading stuff before commenting on it :oops:


:ilove:

I dont want to seem picky but....


step 6 is all you need to do to patch the navcore, following it up with step 9 is pointless as easyusertools is not able to patch v8 navcores from 8.002 onwards and if you've done step 6 its already patched!

:ilove:
terrytpot,

6- Open the folder : SE_ttsystem.8.410.1218 (downloaded)
- Copy the file ttsystem and paste it in the root of your GO910
9- Install the map :
- Install the folder(s) of your map(s) (downloaded) to the root of your GO910
- Open the folder : Easyusetools_for Keygen_Mapcheck_Metacheck_ttsystempatcher (downloaded)
Double click on : Easyusetools_for Keygen_Mapcheck_Metacheck_ttsystempatcher
Double click on : RunMeforAllAutomatic.cmd
Select : 1 or follow the onscreen instructions

Easyusetools is use for patching the map and not the ttsystem

:oops2:,my mistake,read the ends of a sentence and saw "doubleclick" and "ttsytempatcher" :ashamed:
can only say :sorry:...

:ilove:
p.s. easyusetools can be used for patching navcores if you're using one from before 8.010.....

:oops2:,my mistake,read the ends of a sentence and saw "doubleclick" and "ttsytempatcher" :ashamed:
can only say :sorry:...

:ilove:
p.s. easyusetools can be used for patching navcores if you're using one from before 8.010.....




Thank you terrytpot you are excused

grard31

Grard31

Have you experienced lockups and a flashing screen with rev1.1 on the GO910.

Grard31

Have you experienced lockups and a flashing screen with rev1.1 on the GO910.
No blockage, but flickering of the screen during the reboot of the device.
Thereafter, the operation is normal.

grard31

Does the GPRS work on the 910 with this build or is it the same as all the other builds that it won't work at all.


Flack

Does the GPRS work on the 910 with this build or is it the same as all the other builds that it won't work at all.


Flack

Answer is no it does not . Just tried it and it disables the traffic so you can't use it .


Flack :shoutout:

My GO910 with SE_Navcore.8.410


480417480418

480419480420

480421


grard31

grard31

Does your GPRS work for traffic update on your setup. And your icons are nothing like my build of 8.410 on my 910

flack

Hi Gizzburn,

Probably you have the x30 icons because you copied the switchfiles without changing model: x30 in model: x40. Go to folder: switchfiles then to folder: config. then to textfile: setconfig. Make the change there... :goodluck:

Gr Tjilitjap

I have tried putting the latest antitheft icon on with the thief running and exclamation mark on my 910 but if I do it shows the start up screen on shutdown instead. Very strange as it works Ok on my ONE V2.

Has anyone got this working on their 910-if so can someone give a link to the antitheft file please.

grard31

Does your GPRS work for traffic update on your setup. And your icons are nothing like my build of 8.410 on my 910

flack
Gizzburn,
I have not antenna RDS/TMC
GPRS is not working for GO910. Read here :
http://www.ipmart-forum.com/showpost.php?p=2564314&postcount=53
If you have phone connected :
TomTom Services icon (Main Menu 1 of 4) and Mobile phone icon (Main Menu 3 of 4) are inversed

grard31

I have tried putting the latest antitheft icon on with the thief running and exclamation mark on my 910 but if I do it shows the start up screen on shutdown instead. Very strange as it works Ok on my ONE V2.

Has anyone got this working on their 910-if so can someone give a link to the antitheft file please.
moggyminor,

antitheftw.bmp for GO910 attached

grard31

moggyminor,

antitheftw.bmp for GO910 attached

grard31


Thanks a lot:thanks:

Hi,

thanks for the how-to !

Unfortunately, my go910 keeps rebooting once I've done all the steps.
I think I followed carefuly the how-to, so is there anything tricky I may have missed which would make the device always reboot ?

Is there any log file I can check to find where something is going wrong ?

Thanks in advance for any help !

Hi,

thanks for the how-to !

Unfortunately, my go910 keeps rebooting once I've done all the steps.
I think I followed carefuly the how-to, so is there anything tricky I may have missed which would make the device always reboot ?

Is there any log file I can check to find where something is going wrong ?

Thanks in advance for any help !
sysedit,

Have you copied MapSettings.cfg from an other map ?
If so : delete it in the folder map

grard31

sysedit,

Have you copied MapSettings.cfg from an other map ?
If so : delete it in the folder map

grard31

MapSettings was here, now I removed it, but now navcore never shows up (it stays at the tomtom splash screen with "find your way the easy way").

Looking at the device, ttgo.bak and ttgo.gif have been created (Easytools is now detecting everything correctly) ; they are re-created if I removed them and restart.

if I unzip switchfiles.zip/Config files on the root without touching them, I get the configuration questions, but it stops at the panel where it tells you that computer voices are not as natural as human voice.

If I just use

model:x30
runclean
changedtext:TomTom GO 940 LIVE

It does not boot. One of the config must be needed, I'll try to find which one... Shouldn't this work out of the box ?

MapSettings was here, now I removed it, but now navcore never shows up (it stays at the tomtom splash screen with "find your way the easy way").

Looking at the device, ttgo.bak and ttgo.gif have been created (Easytools is now detecting everything correctly) ; they are re-created if I removed them and restart.

if I unzip switchfiles.zip/Config files on the root without touching them, I get the configuration questions, but it stops at the panel where it tells you that computer voices are not as natural as human voice.

If I just use

model:x30
runclean
changedtext:TomTom GO 940 LIVE

It does not boot. One of the config must be needed, I'll try to find which one... Shouldn't this work out of the box ?

remove the all just install se 8410version and se ttystem remove also switchfiles which is included in navcore.
copy what i give you switch update files .now you have all emu works and you don,t need change any text. after go to menu find and push switch x20 x30x40 you try it. switch x40 is the original of navcore 8410 emu.
sorry for my english but so easy to do.

enjoys
thanks

Ok, I've redone evrything from scratch and now it seems to work.

The issue is likely to be that I copied some files from my old map to the new map folder.
=> don't do this at all :).

Thanks all for your help, the howto is perfect, thanks for the file, and thanks for the switch tool too.

sysedit,

Observe the proceedings and not to innovate : why modelx30.... :confused:

It works for me and many others

Ignore the post varjomies

grard31

yep, my initial mistake was to copy files from my old map to the new map folder ; afterwards I was a bit lost and tried other - but useless - ideas.

:thanks:

:Dyep, my initial mistake was to copy files from my old map to the new map folder ; afterwards I was a bit lost and tried other - but useless - ideas.

:thanks:
sysedit,

for you it works, it's perfect :D

grard31

Upgrading from 8.204 and following the instructions - 825 maps are visible but I've lost voices. After starting, the message appears:

Warning:
There are no voices available. You will not hear any spoken instructions.

I copied the new Loquendo folder and added the voice folders from my save. When I attempt to change voices, the choices I'm given are Daniel and Emily (English UK). In my Loquendo folder are Simon and Kate; they worked fine in 8.204.

[edit]

Copying several .so files (which were not in the downloaded Loquendo folder) from my backup LoquendoTTS/lib folder solved the problem. I still do not have ASR; I copied the ASR folder from my 8.204 backup.

pilotman,

Read : http://www.ipmart-forum.com/showpost.php?p=2576618&postcount=33

grard31

pilotman,

Read : http://www.ipmart-forum.com/showpost.php?p=2576618&postcount=33

grard31

Hei grard31 ok they,ll ignore my post if you did not like. but please don,t accuse. it,s works much better and it gives 5 different emu,maybe peoples like that . i,m using tt 910 from
the config text tt was freezing or emu was missing did you ever tried.
you did not answer last friend question he ask tts voice and loquendo tss what is included in your text, it,s not work . if you show in the loquendo tss computer voices how can it will work in navcore 8410 we will
glad and give you more reb.
don,t misunderstand me please

thanks

Hei grard31 ok they,ll ignore my post if you did not like. but please don,t accuse. it,s works much better and it gives 5 different emu,maybe peoples like that . i,m using tt 910 from

thanks
varjomies,

Anything that you can have with GO910 is in the configuration x40
In this configuration (x40 I propose in my procedure) it works perfectly
Why do you want to remove features with emu ? :confused:
Respect the procedure and all works TTS ASR ...

grard31

pilotman,

Read : http://www.ipmart-forum.com/showpost.php?p=2576618&postcount=33

grard31

Comment removed. It's always a good idea to read instructions CAREFULLY - and then follow them. Thanks grard31. All seems to work ok. I'm taking it on the road this afternoon.

Stick with 8.204...this release is VERY unstable :(

2nd post and now already making conclusions !
Nice !

What the hell is unstable with 8.410? I've just upgraded mine and everything works flawless. Be more specific...otherwise no one can help ya.

Hi
I done all on 910 with map USA 835.2157 and full Europe 825.2157 all working except Address vocie input!!
even oice control works!
tested with navcore 8204 and same fault
Voice address input is on menu but is not selectable!

Please adbvise?
thanks

Hi
I done all on 910 with map USA 835.2157 and full Europe 825.2157 all working except Address vocie input!!
even oice control works!
tested with navcore 8204 and same fault
Voice address input is on menu but is not selectable!

Please adbvise?
thanks
- Have you the folder ASR (20450368 bytes) in the root of your GO910 ?
- In the file setconfig.txt only : runclean and changedtext:TomTom GO 910...?
- In Preferences 4 of 8/Voice Cntrol preferences/Enable Voice Control

grard31

Hi Everyone,

Another issue i would like to resolve. Actually 2 - Firstly using Nav 8.410 i can not get my MP3's to show in my music folder on my tomtom. They were working fine when running NAV 8.2......Any ideas.
Put simply they do not show on my Tomtom. Not even a song folder just Download reader, ipod control and Photo galley NO song folder. And yet when i hook the Tommy to my Pc i have a MP3 folder. LIke i said only b4:ilove: since i updated to Nav 8.4 has this presented a problem.

And secondly When i add a poi with a sound file under the same name
IE - Say um KFC poi with a OGG sound file POI - Nav 8.4 doesnt allow me to add this sound file to that POI. Yes they are written exactly the same.
Navcore doesnt allow me to get pass the screen where you enter how far away from the poi do you wanna be alerted. Doesnt matter what i do it wont allow me to proceed to the next screen.
Interesting one that ....

Any one with an idea ....i would love to hear from you

Hi Everyone,

Another issue i would like to resolve. Actually 2 - Firstly using Nav 8.410 i can not get my MP3's to show in my music folder on my tomtom. They were working fine when running NAV 8.2......Any ideas.
Put simply they do not show on my Tomtom. Not even a song folder just Download reader, ipod control and Photo galley NO song folder. And yet when i hook the Tommy to my Pc i have a MP3 folder. LIke i said only b4:ilove: since i updated to Nav 8.4 has this presented a problem.

And secondly When i add a poi with a sound file under the same name
IE - Say um KFC poi with a OGG sound file POI - Nav 8.4 doesnt allow me to add this sound file to that POI. Yes they are written exactly the same.
Navcore doesnt allow me to get pass the screen where you enter how far away from the poi do you wanna be alerted. Doesnt matter what i do it wont allow me to proceed to the next screen.
Interesting one that ....

Any one with an idea ....i would love to hear from you
stefe2009,

For GO910 read here, no problem :D

http://www.ipmart-forum.com/showpost.php?p=2568266&postcount=1

grard31

Gizzburn,
I have not antenna RDS/TMC
GPRS is not working for GO910. Read here :
http://www.ipmart-forum.com/showpost.php?p=2564314&postcount=53
If you have phone connected :
TomTom Services icon (Main Menu 1 of 4) and Mobile phone icon (Main Menu 3 of 4) are inversed

grard31

GPRS is working on my 910 with X30 emulation with one exception: when beeing connected to the car cradle the TT traffice services do not work. This is because RDS-TMC is always beeing switched on and therefore the TT traffic services are not availbale (the same as with the original Navcore 7.xxx where TT traffice services are switched off when the RDS-TMC receiver has been plugged into the car cradle - but 8.410 simply ignores if the receiver is plugged in or out, it always switches on RDS-TMC instead of TT traffic services). Other services (i.e. Wheather, QuickFix) are working perfectly. Even TT traffic is working when the 910 is out of the cradle (however this is not really helpful).

After having installed the 8.410 files on the 910 I have copied the following files from an 8.3xx working configuration:

ttgo.bak
ttgo.bif
connect2internet.db
connect2internet.db.encode
connect2internet.so
connect2internetdb.ver

and the directory "phone_database" from the root folder with the file connect2internet.tlv included in this directory.

With this I was able to connect to my TomTOm account via GPRS and use the TT services (as far as they are available for me with respect to my subscriptions).

Regards, TomTomFan

Cant seem to get my MP3's to show in the music folder of mt tomtom 910 using this Navcore.
When i connect tomtom to PC folder is there smiling at me.
But wont show on my tomtom
WHY????????????????

Cant seem to get my MP3's to show in the music folder of mt tomtom 910 using this Navcore.
When i connect tomtom to PC folder is there smiling at me.
But wont show on my tomtom
WHY????????????????
stefe2009,

I do not know what you did ...
For me MP3 works (no problem)

grard31

stefe2009,

I do not know what you did ...
For me MP3 works (no problem)

grard31

Hi grard,

how does MP3 work on your 910? I have a directory called mp3 in the root folder and copied some mp3-files into this directory. It works perfect on all Navcore 8.3xx versions, but in 8.410 there is only one icon calld "iPod" which can not be activated, the system says "no Ipod connected" (or something similar). So I can not play the mp3 files like I did before. Do you have a solution for this?

GPRS is working on my 910 with X30 emulation with one exception: when beeing connected to the car cradle the TT traffice services do not work. This is because RDS-TMC is always beeing switched on and therefore the TT traffic services are not availbale (the same as with the original Navcore 7.xxx where TT traffice services are switched off when the RDS-TMC receiver has been plugged into the car cradle - but 8.410 simply ignores if the receiver is plugged in or out, it always switches on RDS-TMC instead of TT traffic services). Other services (i.e. Wheather, QuickFix) are working perfectly. Even TT traffic is working when the 910 is out of the cradle (however this is not really helpful).

After having installed the 8.410 files on the 910 I have copied the following files from an 8.3xx working configuration:

ttgo.bak
ttgo.bif
connect2internet.db
connect2internet.db.encode
connect2internet.so
connect2internetdb.ver

and the directory "phone_database" from the root folder with the file connect2internet.tlv included in this directory.

With this I was able to connect to my TomTOm account via GPRS and use the TT services (as far as they are available for me with respect to my subscriptions).

Regards, TomTomFan

UPDATE: TomTom Traffic services is working also when 910 is connected to the car cradle! It can be done by switching the 910 off and on again when in the cradle without having connected the TMC receiver. By doing this the RDS-TMC function gets disabled. After that pressing the "Traffic service" icon (don't know what the correct english description is since I am using a german navcore version) in the menu for some seconds will enter the menu structure for the traffic services where it can be enabled. After that it connects via GPRS to the TomTom server and traffic information is available from there (provided there is a valid subscription).

Hi grard,

how does MP3 work on your 910? I have a directory called mp3 in the root folder and copied some mp3-files into this directory. It works perfect on all Navcore 8.3xx versions, but in 8.410 there is only one icon calld "iPod" which can not be activated, the system says "no Ipod connected" (or something similar). So I can not play the mp3 files like I did before. Do you have a solution for this?

tomtomfan,

Do you have a solution for this?: Yes => Observe the proceedings and not to innovate :hehe:

My GO910 navcore SE 8.410 ==> Photos MP3 !!!... :good2:

grard31

tomtomfan,

Do you have a solution for this?: Yes => Observe the proceedings and not to innovate :hehe:

My GO910 navcore SE 8.410 ==> Photos MP3 !!!... :good2:

grard31

The solution is to use FMon (or at least NOT using FMoff) in the switch files, as I have read on a german bulletin board. Tried to use FMon which resolved the problem. Nothing to do with the proceedings described earlier in this post.

The solution is to use FMon (or at least NOT using FMoff) in the switch files, as I have read on a german bulletin board. Tried to use FMon which resolved the problem. Nothing to do with the proceedings described earlier in this post.
tomtomfan,

You do not understand the procedure :hehe:

Navcore SE 8.410 is naturely of x40
It is therefore unnecessary to specify in the file setconfig.txt => x40
In the same way fmon, needless to say
Before you criticize : apply the procedure

Your words are off topic

grard31

Hello Experts,

Just upgraded my TT GO 910 from navcore 7903 (patched) -> 8.410.1218 rev1.1. I am using the map "Central and Western Europe" 8.25 2157. Followed the instructions as mentioned on the first page by grard31. Thanks a lot grard31 for the excellent compilation of instructions, has really helped to get things working.

I have a problem though. I have chosen English UK and Kate as the voice, but there are no voice instructions after planning the route or on the route. To sort out I have already tried the following:
1) Erased Go910 once again and followed the instructions line by line. But still have the same problem. :(
2) I have tried to change the voice to Simon US and test. The test (button) works OK and I hear the voice. But on road, no voice instructions.
3) Took the Go910 on a route, I received the beep if I exceed speed limit, but there are no voice instructions.
4) The speaker setting are correctly configured to output sound via internal speaker.

Note that this is the first time I have used SE version on my Go910. Am I required to download new LoquendoTTS voice files?
Further I had a minor confusion about the installation instuctions, where it is mentioned to copy the loquendoTTS (in step 4) to the root. The step 5 mentions to copy the contents of SE_Navcore.8.410.1218.Basicpack to the root. The basic pack also contains loquendoTTS, but I have not copied this folder again as it would have overwritten the existing loquendoTTS folder with all the voice files already present. Did I do something wrong here?
In the "Volume Preferences", I have set the volume to 85%, but clicking the "Test" does not result in any voices\noises? Is it normal? Have not tried going back to navcore 7903 yet to ensure it still works there (it was working earlier).

Must say this is a great forum. Three cheers !!!

Thanks for help.

alwak,

Note that this is the first time I have used SE version on my Go910. Am I required to download new LoquendoTTS voice files? => no

The basic pack also contains loquendoTTS, but I have not copied this folder again as it would have overwritten the existing loquendoTTS folder with all the voice files already present. Did I do something wrong here? => yes (but in the file setconfig.txt you have only runclean and changedtext:..?)

For you :
- In your GO910 : delete the folder LoquendoTTS
- Install the folder LoquendoTTS (6357786 bytes downloaded) to the root of your GO910
- From the saved copy of your GO910 : in the folder LoquendoTTS make a copy folders Dutch, EnglishGb, EnglishUs, French, German, Italian, PortuguesePt, Spanish then paste them inside the folder LoquendoTTS (previously installed) on your GO910. Close the folder LoquendoTTS
- Open the folder : SE_Navcore.8.410.1218.Basicpack (downloaded)
- Copy the folder LoquendoTTS and paste it in the root of your GO910 (select all)

grard31

tomtomfan,

You do not understand the procedure :hehe:

Navcore SE 8.410 is naturely of x40
It is therefore unnecessary to specify in the file setconfig.txt => x40
In the same way fmon, needless to say
Before you criticize : apply the procedure

Your words are off topic

grard31

grard31

I think you do not understand what I have written. First of all: I have not criticized anything!

I followed the procedure you have described here - and many thanks for this, it's very good. I have not changed anything in the setconfig.txt from what you have written, and did not specify x40 there (i don't know why you have mentioned this, I never said that I did it).

But: the TomTom Jukebox did not appear on my GO910! :confused:

And the solution to fix it was to specify FMon in the setconfig.txt, believe it or not. :hahaha2:

After I did this the TomTom Jukebox was available and I can now play my MP3-Files. :hehe:

So please tell me why you have a problem with the description of this solution and why do you think it is off-topic?

grard31

I think you do not understand what I have written. First of all: I have not criticized anything!

I followed the procedure you have described here - and many thanks for this, it's very good. I have not changed anything in the setconfig.txt from what you have written, and did not specify x40 there (i don't know why you have mentioned this, I never said that I did it).

But: the TomTom Jukebox did not appear on my GO910! :confused:

And the solution to fix it was to specify FMon in the setconfig.txt, believe it or not. :hahaha2:

After I did this the TomTom Jukebox was available and I can now play my MP3-Files. :hehe:

So please tell me why you have a problem with the description of this solution and why do you think it is off-topic?
tomtomfan,

If you followed the procedure, I assure you that the swithchfile fmon is unnecessary (this switchfile is for use in other settings, but not this one)
As for navcore SE 8.204, read here:
http://www.ipmart-forum.com/showpost.php?p=2481690&postcount=1
For 8.204 -Open file setconfig.txt, keep only changedtext:TomTom GO 940 LIVE (delete all other files), delete 940 LIVE, write for example : 910 with your name, close the file setconfig.txt

grard31

tomtomfan,

If you followed the procedure, I assure you that the swithchfile fmon is unnecessary (this switchfile is for use in other settings, but not this one)
As for navcore SE 8.204, read here:
http://www.ipmart-forum.com/showpost.php?p=2481690&postcount=1
For 8.204 -Open file setconfig.txt, keep only changedtext:TomTom GO 940 LIVE (delete all other files), delete 940 LIVE, write for example : 910 with your name, close the file setconfig.txt

grard31

Hi grard31,

OK I trust you. I will delete evrything on my 910 and do a complete fresh installation according to your procedure, I am sure it will work as you have described.

Do you know if GPRS is working on the 910 with your procedure? I managed to get it work only with x30 emulation, not in x40 mode.

Again thank you very much for your great work! :thanks:

I have aquired a Tomtom 510 and wondered if anyone could advise which navcore to install on it please? There are obviously a few versions available on here and would prefer to install one that has been tested on a 510. Thank you. I am familiar with the 720 and 730 but not the 510.

I have aquired a Tomtom 510 and wondered if anyone could advise which navcore to install on it please? There are obviously a few versions available on here and would prefer to install one that has been tested on a 510. Thank you. I am familiar with the 720 and 730 but not the 510.

NC 8.320.9732 runs very good on the x10 Series. 8.410.1218 is also good but has some little problems.

Thank you. Will give it and try over the next few days. I have searched this forum and cannot find 8.320.9732. Can anyone help with a link please?:thanks:

With G0910 object of topic : only the GPRS does not work (already reported post 10 and 20)
Each version has its advantages and disadvantages
Here, the subject is navcore 8.410 for GO910

grard31

Thank you. Will give it and try over the next few days. I have searched this forum and cannot find 8.320.9732. Can anyone help with a link please?:thanks:
Read here : http://www.ipmart-forum.com/showthread.php?t=305111&highlight=navcore+8.300

grard31

:yourock: grard

:dance: :dance: :dance: :dance:

My Go910 is now working and Kate has started speaking to me.

:2thumbsup:
:ilove: This is a great forum.

Hi,

I've tried this new navcore according to this procedure with my GO 910 and it works very well :

Big RAM memory with or without the folder outsourced.bin.

TTS Voices work well :good2:

I used only changedtext for switchname inside file setconfig.txt

No more problem of big sound level :good2:

:dance: :dance:


:thanks: Grard31

With G0910 object of topic : only the GPRS does not work (already reported post 10 and 20)
Each version has its advantages and disadvantages
Here, the subject is navcore 8.410 for GO910

grard31

grard31

Is the GPRS issue ever going to be sorted for the 910, this all that stops me from using version 8 on my 910.

Flack

grard31

Is the GPRS issue ever going to be sorted for the 910, this all that stops me from using version 8 on my 910.

Flack
Read here : http://www.ipmart-forum.com/showpost.php?p=2586571&postcount=52

But if you want to talk about this : open another topic on the forum. Thank you.

grard31

hii grard31

tt 910 turn on so late n. 3 min sometimes need reset . how can we fix ?

thanks

Hi, thanks grad for this tutorial!
Sorry for the stupid question, but where could i find switchfile.zip?
:)

Oups, i found it, sorry.

hii grard31

tt 910 turn on so late n. 3 min sometimes need reset . how can we fix ?

thanks

Sorry varjomies,

As you have configured your GO910, I do not assist you
Read : http://www.ipmart-forum.com/showpost.php?p=2576510&postcount=31

You are the only person to have this problem ...
For alwak, gpsmap, me and many others : no problem

I advice you to open a new thread, on the forum, and I am sure you have the answer

grard31

this version of navocre is really great in terms of interface :good2: but there are a few issues with it, or at least for me!
1. allthough i can select the voices and test them they don't actually play in the background when they should (turn left and so on)
2.the poi that i have seem not to be working at all!!! and on tomtom home the option to download them appears to be unavailable for "my device" as it says!-this is the same for car symbols!

If this probs could get sorted, then this would be by far the best goodlooking navcore out there.

thanx anyway for all the hard work you have put into compiling all the instructions! :urtheman::urtheman::urtheman::thanks:

Hi,

I've managed to sort out the problem with the voice, all i've done i've deleted the loquendo TTS that i was having on the root of my go910 after that i went to the backup copy that i've made initially after the patched 8.300 and i've copied the whole loquendo TTS to the root of my go910. now there are no more problems with the voices but i still can't make the poi to work! any sugestions anyone?:shoutout:

I think i've found what it is it! from change preferences menu next to the use night/day colours is a faded icon which should've enable me to "Show POI on map"! any ideas how can i activate that one?:oom:

sorry varjomies,

as you have configured your go910, i do not assist you
read : http://www.ipmart-forum.com/showpost.php?p=2576510&postcount=31

you are the only person to have this problem ...
For alwak, gpsmap, me and many others : No problem

i advice you to open a new thread, on the forum, and i am sure you have the answer

grard31

hei grard31 read the all thread in all thread SAME PROBLEM and also maveric is compilaining same case also in others don,t tell me you,re only one , you.re not telling true. I thought this is the sharing form and all users free to write them idea and thoughts.
Maybe it will be wrong . I,m sure you also don,t know how to fix
that,s thev really reason runaway.

Be sure ydg is the best mod,also ttuser, big dave, maveric , terry poth they,ll never act same like you , they always try to teach and help us. They,re the best.

Now i don,t mind you assist me or not.

found it!
it looks like with the map that i got i did not have any poi!
so what i've done i went again to my backup map 815 and i've copied all the files related to poi paste them and now all is k. i love this version!!!
big thank you again to all you who made this possible!:thanks:

grard31 i understand this is a thread for go 910 but would like to try this on my bog standard tomtom one v2.
is this possible?? :ilove:

Hi,

I've managed to sort out the problem with the voice, all i've done i've deleted the loquendo TTS that i was having on the root of my go910 after that i went to the backup copy that i've made initially after the patched 8.300 and i've copied the whole loquendo TTS to the root of my go910. now there are no more problems with the voices but i still can't make the poi to work! any sugestions anyone?:shoutout:
arpiriki,

For the folder LoquendoTTS:
- In your GO910 : delete the folder LoquendoTTS
- Install the folder LoquendoTTS (6357786 bytes downloaded) to the root of your GO910
- From the saved copy of your GO910 : in the folder LoquendoTTS make a copy folders Dutch, EnglishGb, EnglishUs, French, German, Italian, PortuguesePt, Spanish then paste them inside the folder LoquendoTTS (previously installed) on your GO910. Close the folder LoquendoTTS
- Open the folder : SE_Navcore.8.410.1218.Basicpack (downloaded)
- Copy the folder LoquendoTTS and paste it in the root of your GO910 (select all)

Before open TTHome, in the file ttgo.bif, check : ApplicationVersionVersionNumber=7903

For the POI, place the files .bmp and .ov2 in the folder of the map
Preferences 1 of 8 / Show POI on map

grard31

grard31 i understand this is a thread for go 910 but would like to try this on my bog standard tomtom one v2.
is this possible?? :ilove:
scottydog90,

It is preferable for tomtom one v2 read here :
http://www.ipmart-forum.com/showthread.php?t=345821

grard31

[/color]

hei grard31 read the all thread in all thread SAME PROBLEM and also maveric is compilaining same case also in others don,t tell me you,re only one , you.re not telling true. I thought this is the sharing form and all users free to write them idea and thoughts.
Maybe it will be wrong . I,m sure you also don,t know how to fix
that,s thev really reason runaway.

Be sure ydg is the best mod,also ttuser, big dave, maveric , terry poth they,ll never act same like you , they always try to teach and help us. They,re the best.

Now i don,t mind you assist me or not.[/U]

varjomies,

I will not refuse to help you but, I do not know the answer to your problem.
Have you followed the procedure ?

grard31

grard31 thanks for your time in pointing me in the right direction
:wave:

varjomies,

I will not refuse to help you but, I do not know the answer to your problem.
Have you followed the procedure ?

grard31

Hi grard31

no problem i spoke to ydg moderator. he promise to fix start up problem if it,s possible let,s wait and see. someone doesn,t care but usually everyones tt are turn on late with se 8410.
thanks anyway for the try to help.

Hi grard31

no problem i spoke to ydg moderator. he promise to fix start up problem if it,s possible let,s wait and see. someone doesn,t care but usually everyones tt are turn on late with se 8410.
thanks anyway for the try to help.
varjomies,

I'm sorry, but I can not have a solution for every problem
I will be happy to know the solution to your problem

In advance I thank you

grard31

Well, I am impressed with the nc 8.410.1218 running on my 910... :dance:

I have tried 8.204 & 8.300 on it prior to this...

I had a problem with getting ASR to work on it, but I found that to be my fault using a wrong choice of ASR folder...

it connects to my motorola phones fine too, with 8.300 it would error...:good2:

works perfectly with the fully featured 825.2157 maps..:egdance:

all appears to working fine, I cannot fault it yet... all I have left to test is my rds-tmc connectivity when I find where I put it... :D


I would recommend this upgrade to any 910 user....:wave:

LoneCrusader

I too have it working ok on my 910 but still the traffic does not work, my phone connects through bluetooth ok but as soon as you connect through home it disables traffic and all my traffic icons show but do nothing when you press them, is there going to be a fix for this ??? I have tried it using x30 emulation and I get the error i have described above.
But when I use the 910 set to original I get the error of can't connect to Tt server or try again later ..

gizzburn

I'm having the exact same problem. It sure would be great is GPRS traffic were fixed. It's the only reason I keep downgrading.

well, I have had a chance to test the 8.410 on my 910 for even longer, it mostly works great except for 3 very annoying features...

1) the turn on time is far too looonggg...

2) it always thinks it has been connected to rds-tmc when plugged into the car cradle even when the rds-tmc is not.. the sidebar stays there gloating... if I then plugin my rds-tmc, the 910 reports its found it & says now connected, if I unplug it, the 910 reports its been disconnected, the sidebar goes away only to return a few seconds later with the 910 reporting its re-connected to rds-tmc when it hasn't... obviously the method of detecting the rds-tmc has changed...

3) I did notice that when the rds-tmc is really plugged in, if I run a demo route, the screen refreshes like as in a short pause before redrawing the roads on the plain background, never noticed this before.... plus rds-tmc stays as searching... I am yet to take it for a drive...

LoneCrusader

I too have it working ok on my 910 but still the traffic does not work, my phone connects through bluetooth ok but as soon as you connect through home it disables traffic and all my traffic icons show but do nothing when you press them, is there going to be a fix for this ??? I have tried it using x30 emulation and I get the error i have described above.
But when I use the 910 set to original I get the error of can't connect to Tt server or try again later ..

gizzburn

I have the following problem. When running this setup all works fine except when I connect the device to the computer it does not give the option to connect so cannot access the device from the computer (mac). Connection works fine on 8.204.

I have the following problem. When running this setup all works fine except when I connect the device to the computer it does not give the option to connect so cannot access the device from the computer (mac). Connection works fine on 8.204.
qualar,

Caution : when you switch off (or on) the GO910 and put it on the cradle, after 45 – 50 seconds it automatically restart and connect to your computer

With windows, with mac...?

grard31

3) I did notice that when the rds-tmc is really plugged in, if I run a demo route, the screen refreshes like as in a short pause before redrawing the roads on the plain background, never noticed this before.... plus rds-tmc stays as searching... I am yet to take it for a drive...

well, I roadtested it today....

it does exactly as above, when the rds-tmc is plugged in, the 1 second road redraw pauses are really annoying while driving, it goes back to normal continuous road display if I simply unplug the rds-tmc from the car cradle...

the rds-tmc refuses to lock on the any signal anyway....

apart from that its just the traffic bar staying displayed, which we know about...




if I never owned a rds-tmc I could live with it, but having a rds-tmc that is not functioning is like a dripping tap, it gets more annoying as time passes

well, I have had a chance to test the 8.410 on my 910 for even longer, it mostly works great except for 3 very annoying features...

1) the turn on time is far too looonggg...

2) it always thinks it has been connected to rds-tmc when plugged into the car cradle even when the rds-tmc is not.. the sidebar stays there gloating... if I then plugin my rds-tmc, the 910 reports its found it & says now connected, if I unplug it, the 910 reports its been disconnected, the sidebar goes away only to return a few seconds later with the 910 reporting its re-connected to rds-tmc when it hasn't... obviously the method of detecting the rds-tmc has changed...


Same on mine.
Everything seems to work well except that it takes nearly 30 sec to start, even if I just turn my car off (it stops 12V power plug).
It looks like it restarts as if it would be the first time its starts: I have to accept the risk that driving with the device may be evil... while it was not the case with the original version.

can anyone else confirm the issue with rds-tmc ? as I wasn't able to remove the side bar, I'm not far from buying a tmc antenna, but if this does not work...

anyway, except that, it works pretty well, thanks again for the howto.
Just an add: if you don't copy your backuped ephem directory, you will not get quick gps fix updated anymore, so don't forget to copy it again.

Hi Everyone,

All working beautifully here on Go 710. Thanks to grard31.

Let's all increase his reputation as this gentleman is awesome
and truly does answer each and everyone of our questions
even if some questions posed makes him feel like hair is
falling out of his head.

:urtheman:

:ilove:

Darren

Hvae you managed to get the text to speach working on the 710? I have tried for days and still not got it working.

Hvae you managed to get the text to speach working on the 710? I have tried for days and still not got it working.
wazzzzupmate,

To make a folder LoquendoTTS, read here: (works with 8.410)
http://www.ipmart-forum.com/showpost.php?p=2597870&postcount=23

grard31

Ok I have done that, copied all the LoquendoTTS folder from the backup to the root of my SD card. The Loquendo TTS folder from the downloaded backup is empty. I have tried a reset. Do I need to do anything with the outsourced.bin files or the model.txt? thanks so far.

Ok I have done that, copied all the LoquendoTTS folder from the backup to the root of my SD card. The Loquendo TTS folder from the downloaded backup is empty. I have tried a reset. Do I need to do anything with the outsourced.bin files or the model.txt? thanks so far.
wazzzzupmate,

No, in your GO, delete the folder LoquendoTTS.
Copy the new folder LoquendoTTS and past it to the root of your GO

grard31

Ok, slightly confused. One the 710 I thought all the files were stored on the SD card. I didn't think it had an internal memory. Am I wrong?
Also is the Loquendo folder are there meant to be any files, as the one in the backup is empty. Thanks again

Installation SE_Navcore.8.410.1218.rev.1.2 for GO910 (voices of original)
Sorry for my English :sorry:
Download Jdownloader :
http://www.anonym.to/?http://jdownloader.org/download/index
For download with JDownloader, read (example) :
http://www.ipmart-forum.com/showpost.php?p=2566284&postcount=15
(By following the example, you have the folder ASR)

- Read :
http://www.ipmart-forum.com/showpost.php?p=2563628&postcount=1
- You should have the folder : ASR (20450368 bytes)
- Download :
http://www.anonym.to/?http://rapidshare.com/files/207488048/SE_Navcore.8.410.1218.Basicpack.rar
Extract the folder : SE_Navcore.8.410.1218.Basicpack
- Download :
http://www.anonym.to/?http://rapidshare.com/files/215275254/SE_ttsystem.8.410.1218.rev.1.2.rar
Extract the folder : SE_ttsystem.8.410.1218.rev.1.2
- Download :
http://www.ipmart-forum.com/attachment.php?attachmentid=448965&d=1227044472
Extract the folder LoquendoTTS
- Download :
http://www.ipmart-forum.com/attachment.php?attachmentid=450399&d=1227432495
Extract the folder suspend
- Download the map you want to use :
For map : Western_and_Central_ Europe 825.2157 or other countries
For map : North_America 825.2157
Maps located in the thread below (in the last pages) :
http://www.ipmart-forum.com/showthread.php?t=337584
For map : Australia 815.2086
Map located in the thread below (in the last pages) :
http://www.ipmart-forum.com/showthread.php?t=337608
Extract the map
- To activate the map, read and download : Easyusetools for Keygen Mapcheck Metacheck ttsystempatcher
http://www.ipmart-forum.com/showpost.php?p=2086254&postcount=58
Extract the folder Easyusetools_for Keygen_Mapcheck_Metacheck_ttsystempatcher

Installation :
1- Save the contents of your GO910 in a safe place on your hard drive
2- Clear all the contents of your GO910
3- Install the folder ASR (20450368 bytes) to the root of your GO910
4- Install the folder LoquendoTTS (downloaded) to the root of your GO910
- From the saved copy of your TomTom : in the folder LoquendoTTS make a copy folders Dutch, EnglishGb, EnglishUs, French, German, Italian, PortuguesePt, Spanish then paste them inside the folder LoquendoTTS (previously installed) on your GO910. Close the folder LoquendoTTS
For those who do not have these folders download the voices :
http://www.ipmart-forum.com/showthread.php?t=170022
5- Open the folder : SE_Navcore.8.410.1218.Basicpack (downloaded)
- Install SE_Navcore.8.410.1218.Basicpack contents of the folder to the root of your GO910 later :
- delete the folders Navcore.8.410.1218@ tomtom.com, Outsourced.8410 and the file readmenot.txt
- unzip the folder switchfiles.zip, open the folder swichfiles, open the folder Config, copy the files setconfig.txt, version.txt and paste them in the root of your GO910
- open the file setconfig.txt, keep only runclean and changedtext:TomTom GO 940 LIVE (delete all other files), delete 40 LIVE, write for example : 10 with your name, add : reduceflicker (write manually), close the file setconfig.txt
- delete the folders switchfiles.zip and switchfiles
6- Open the folder : SE_ttsystem.8.410.1218.rev.1.2 (downloaded)
- Copy the file ttsystem and paste it in the root of your GO910
7- Open the folder suspend (downloaded), copy the file suspend.ogg and paste it in the root of your GO910
8- Add the folders and files you want from your backup :
- Folders : art, audiobooks, contacts, ephem, helpme, itn, mp3, photos, raster, sounds, zip ...
- Files : antitheftw.bmp, autorun.inf, splashw.bmp, suspendw.bmp, tomtom.ico ...
9- Install the map :
- Install the folder(s) of your map(s) (downloaded) to the root of your GO910
- Open the folder : Easyusetools_for Keygen_Mapcheck_Metacheck_ttsystempatcher (downloaded)
Double click on : Easyusetools_for Keygen_Mapcheck_Metacheck_ttsystempatcher
Double click on : RunMeforAllAutomatic.cmd
Select : 1 then 1 and follow the onscreen instructions
10- Disconnect the GO910, let it reboot (select in Windows “Safe disconnect”, disconnect GO910 from the computer (take it from a cradle)) Wait the message : Create ttgo.bak (about 1 minute)
11- Making various settings
12- Switch off and then turn on the GO910 to properly save the configuration

Caution : when you switch off the GO910 and put it on the cradle, after 45 – 50 seconds it automatically restart and connect to your computer.

For TTHome2 : I use the old method (I do not handle my GO910 with TTHome)
With XP :
Open folder : SE_Navcore.8.410.1218.Basicpack (downloaded), open the folder Navcore.8.410.1218@ tomtom .com, copy the file 8-410-1218-1.dll
In C:\Documents and Settings\ ????????\Application Data\TomTom\HOME\Profiles\xxxxxxxx.default\extensi ons\Navcore.7.903.9183@tomtom.com (or other), I paste file 8-410-1218-1.dll, I note the file name .dll (7-903-9183-1.dll (or other)), I delete the file : 7-903-9183-1.dll (or other), and I rename file 8-410-1218-1.dll : 7-903-9183-1.dll (or other)
With Vista : C:\Users\????????\AppData\Roaming\TomTom\HOME\Prof iles\xxxxxxxx.default\extension\Navcore.7.........
:thanks: :thanks:
Bonne route et merci TTuser :urtheman: :urtheman:
grard31

For those who have the rev1.1 :

- In your GO910, delete the files : ttgo.bak, ttgo.bif, ttgo.ori,TTPnPD (if you have) and ttsystem
- Open the folder : SE_ttsystem.8.410.1218.rev.1.2 (downloaded)
Copy the file ttsystem and paste it in the root of your GO910
- Open the folder : SE_Navcore.8.410.1218.Basicpack (downloaded), open the folder swichfiles, open the folder Config, copy the file version.txt and paste it in the root of your GO910
In your GO910 open the file setconfig.txt, add : reduceflicker (write manually), close the file setconfig.txt
- Disconnect the GO910, let it reboot (select in Windows “Safe disconnect”, disconnect GO910 from the computer (take it from a cradle)) Wait the message : Create ttgo.bak (about 1 minute)
- Switch off and then turn on the GO910 to properly save the configuration

Now : Installation SE_Navcore.8.410.1218 rev1.2 for GO910 (voices of original)
Read here :
http://www.ipmart-forum.com/showpost.php?p=2599747&postcount=101

Thank you :wave:

grard31

What is the difference to revision 1.1 in the other posting??

What is the difference to revision 1.1 in the other posting??
Viennaboy,

Problem solved : traffic vertical bar RDS/TMC

grard31

Thanks. Can you confirm if the 710 has an internal memory as well as the SD card. I am use to using the 730 which has both, but my PC only shows the SD card for the 710

710 have definitely no internal mem, only a SD

A GO710 only has the SD, no internal memory to store maps.
A GO910 only has the internal memory (20Gb harddisc), but no SD...

Gr Tjilitjap

TTuser was faster :rofl:

Hey Grard,

Did TTuser bring out this rev 1.2 :solution to RDS-TMC bar?

Thanks in advance gr Tjilitjap

Cheers, so the Loquendo folder must go on the root of the SD card. Fingers crossed this time. Do I need to set the model.txt to a certain version?

Hey Grard,

Did TTuser bring out this rev 1.2 :solution to RDS-TMC bar?

Thanks in advance gr Tjilitjap

tjilitjap,

Yes, this is perfect !... :egdance:

grard31

IT IS WORKING!! IT IS WORKING!! Finally I am relieved from this TMC-bar...

Thanks Grard ans special thanks too TTUSER, the man who did it again!!! :ilove:

Correct is to edit post #1 with update
threads merged

with rev 1.2, the rds-tmc bar now works just as it should, only appears when a real rds-tmc is plugged into the 910 car-cradle... a brilliant step forward....


screen flickers same as before (only when the rds-tmc lead is plugged into cradle) maybe some system interupt caused as unit tries to access the rds-tmc...?




not that I can get my rds-tmc to lock in on any signal on my 910, yet....

Correct is to edit post #1 with update
threads merged

Dear dragonhttp://www.google.fi/images?q=tbn:RzMEEZAredWr3M::img291.imageshack.us/img291/1269/youngdragonhy9.gif (http://www.google.fi/images?q=tbn:RzMEEZAredWr3M::img291.imageshack.us/img291/1269/youngdragonhy9.gif)

what about the turn on time is far too looonggg...did you solved this trouble ?

thanks.


SE_Navcore.8.410.1218.Basicpack.rar (http://www.anonym.to/?http://rapidshare.com/files/207488048/SE_Navcore.8.410.1218.Basicpack.rar)

SE_ttsystem.8.410.1218.rev.1.2.rar (http://www.anonym.to/?http://rapidshare.com/files/215275254/SE_ttsystem.8.410.1218.rev.1.2.rar)

ASR Folder for Voice Input can you use one from 8.2, 8.3

all additional SE Features, Function, Use similar as already known, read readme for exact Infos

Changelog:
30.03. rev1.2 try to fix always started TMC, try to reduce screenflicker, switch on with switch "reduceflicker"

10.03. now again a basicpack + single ttsystem or i goes crazy with uploading always all new
again inbuilt "Solution" for x00 GPS Prob
x40light changed a little, heard this works better, old x40light now under x40light2 available

EDITED BY TTUSER

PROBLEM SOLVED

YES GUYS THAT,S WORKS MUCH BETTER THAN BEFORE THANKS A LOT TTUSER I ALREADY GAVE YOU REB.
THANKS TO TTUSER AND YDG , Grard31 for the helpfull tread

Antenna RDS/TMC works

:wave: :dance2: :wave: :dance2: :wave: :dance2: :wave:

I just bought an antenna RDS / TMC for my GO910

It works. (reference: 4V00.013) I had the information on my route there was no problem

The only small problem: every 10 seconds there is a jump to the screen image

But I am almost sure that TTuser will solve this problem

grard31

@grard31 What do you mean with a jump to the screen image? Is the navigation window lagging behind you actual position nad then jumps further again?

@grard31 What do you mean with a jump to the screen image? Is the navigation window lagging behind you actual position nad then jumps further again?
vincentn1981,

No, this is none of this.
It's like blinking of the eyelids, the image disappears and comes back instantly.
The phenomenon occurs when the antenna is connected (every 9-10 seconds). Whether looking for a station that broadcasts traffic information or is in receipt

grard31

Antenna RDS/TMC works

:wave: :dance2: :wave: :dance2: :wave: :dance2: :wave:

I just bought an antenna RDS / TMC for my GO910

It works. (reference: 4V00.013) I had the information on my route there was no problem

The only small problem: every 10 seconds there is a jump to the screen image

But I am almost sure that TTuser will solve this problem

grard31

with the 8.410....! whats different about yours then...?

I got it to work fine on my oneXL with 8.204, but....
on my 910 running 8.410 it keeps searching forever! besides having that annoying .5-1 second pause with the road detail missing every umpteen seconds... the background is as it should be, its just the road detail missing for that .5 to 1 seconds a time when the rds-tmc is plugged in....



the system turnon delay is really winding me up....

with the 8.410....! whats different about yours then...?

I got it to work fine on my oneXL with 8.204, but....
on my 910 running 8.410 it keeps searching forever! besides having that annoying .5-1 second pause with the road detail missing every umpteen seconds... the background is as it should be, its just the road detail missing for that .5 to 1 seconds a time when the rds-tmc is plugged in....



the system turnon delay is really winding me up....
LoneCrusader,

What has changed compared to the procedure : I put the switch => reduceflicker (reduces flicker when reboot)
Read here : : http://www.ipmart-forum.com/showpost.php?p=2601417&postcount=449
http://www.ipmart-forum.com/showpost.php?p=2602778&postcount=458

What has changed in my GO910 : in the folder gns now I have a file gnsdata (16440 bytes), created at a time when I received for the first time traffic information

(I've disabled my folder screen => hence no photo of the screen)

Now the procedure rev.1.2 is updated

grard31

Screenshot of my GO910, antenna RDS/TMC connected

Phone not connected

485708485709

Phone connected

485710485711


grard31

Hi, someone has the Tom Tom services working on Go 910?
Thanks.

Sorry for my bad English.

Just upgraded.
Looks to boot much faster than before, and the TMC bar is no more present.

Thanks ! Thanks ! Thanks ! :)

@grard31: have you bought the antenna online ? If yes, could you share where ?
Have a nice week-end !

Just upgraded.
Looks to boot much faster than before, and the TMC bar is no more present.

Thanks ! Thanks ! Thanks ! :)

@grard31: have you bought the antenna online ? If yes, could you share where ?
Have a nice week-end !
Thank you sysedit,

Search on Ebay : antenna RDS/TMC, but only reference => 4V00.013

grard31

Hi, someone has the Tom Tom services working on Go 910?
Thanks.

Sorry for my bad English.
Ocram60,

I can not answer, I have no GPRS subscription, but it seems to me that not.

grard31

Hi, someone has the Tom Tom services working on Go 910?
Thanks.

Sorry for my bad English.

No bud GPRS does not work, I have tried for hours to get it to work, as soon as your unit connects to the TT server with 8.410 installed it disables traffic and all you get is cannot connect to service when you try.
All the other features work well on my 910 its just a shame the whizz guys on here can't sort out the GPRS, as this would make the 910 on a par with the new models.

I have a fully paid subscription to TT traffic but I have just ordered a RDMC / TMC cable so I can use 8410 software.
I think for £20.00 for the cable ( if it works ) is a lot cgeaper than buying a new unit with these functions, I am willing to forget about my subscription if it works.

Gizz:good2:

I suggest that you try this (I did, thinking it was a recipe for Grandma. Read on another forum)
In the car :
- Install the antenna (reference: 4V00.013)
486170
(thank : tomtom newbie)
- Connect the antenna RDS/TMC to your GO910 (the vertical bar appears)
- Connect the power supply (cigarette lighter plug => green LED on the GO910)
- Change the map (eg North America)
- Return to your map normally used
- You travel by car in an area where reception of the traffic is good info ...

grard31

today something strange happened with my 910 running its 8.410...

I turned it on, screen appeared reasonably quick... instead of the long bootup delay its had since installing this 8.410...:dance2:

I setoff, before I reached the end of the turning, the screen 1 second break in road refresh disappeared & my green circle appeared showing my rdshad connected... :excited:

I was amazed as it behaved totally different today, I was even going to revert back to 8.204 too as I knew the rds works fine on that, but, by the looks of it, theres no need to..........

seems all normal now....

all the 3 probs seems to have gone away

Thanks been trying for ages to get this far with my 910 you are the man

hi, Grad31
thank you for your poster. but the link which at first pages for download , they are all not working anymore. for example: for download the following files:
SE_Navcore.8.410.1218.Basicpack, link doesn't work,
pls help me. you may be upload to BT networking. for us to download

Thks

hi, Grad31
thank you for your poster. but the link which at first pages for download , they are all not working anymore. for example: for download the following files:
SE_Navcore.8.410.1218.Basicpack, link doesn't work,
pls help me. you may be upload to BT networking. for us to download

Thks
crabmom2009,

Try again, all links works :nod:

grard31

thank you excellent guide :)

Hi guys,

is anyone able to use the "voice recognition" commands? my one appears to be shaded in the preferences menu and i dont know how to sort it out!

any ideas?

thanx

Hi guys,

is anyone able to use the "voice recognition" commands? my one appears to be shaded in the preferences menu and i dont know how to sort it out!

any ideas?

thanx
arpiriki,

Read here :
http://www.ipmart-forum.com/showthread.php?t=346473

grard31

a million thanks grard31

now is working perfectly fine.
:urtheman::urtheman::urtheman: :yourock::yourock: :thanks:

:ilove:

@ grard31
Thanks my friend, good work...
Every thing is working well with your method and map WCE.2GB.825.2157:yourock:
Exept i can't set light sensor (by touch nor by voice command)
This is minor "bug" but i LOVE when everything is perfect...
Any idear ? :ooppss:
PS : I LOVE IPMART

Exept i can't set light sensor (by touch nor by voice command)
This is minor "bug" but i LOVE when everything is perfect...
Any idear ?
krystofetbob,

For me, all functions of the light sensor works :

1 - automatic (Switch to night view when dark : checked)

2 - manual : Brightness preferences / Day colour brightness from 0 to 100%
Night colour brightness from 0 to 100%

3 - Voice Control :
Brightness down, Brightness up
Day view, Daytime view, Decrease brightness
Increase brightness
Night view, Nighttime view
Turn brightness down, Turn brightness up, Turn down brightness, Turn up brightness
Use day colours, Use night colours

grard31

Many thanks this works great ;-) :urtheman:

@ grard31
Thanks for answer
One more thing : does your light sensor work when you are docked and/or undocked to the windscreen mount ?
Mine doesn't want to work with this navcore....Hummm....Strange...
i will try to find the issue....
@+

@ grard31
Thanks for answer
One more thing : does your light sensor work when you are docked and/or undocked to the windscreen mount ?
Mine doesn't want to work with this navcore....Hummm....Strange...
i will try to find the issue....
@+
krystofetbob,

It works for me with or without the car mount... :nod:

grard31

i now have some very jealous friends thanks to you would this work on his 510?
thanks

i now have some very jealous friends thanks to you would this work on his 510?
thanks
palacebob,

I do not know how to answer, each device is different
You can try ... and you will see ...

grard31

palacebob,

I do not know how to answer, each device is different
You can try ... and you will see ...

grard31

I agree....



palacebob, yours friends jealousy may easily turn to anger if you bugger his up... so be careful....

i have 2 510 work perfectly

@ grard31
Thanks for answer
One more thing : does your light sensor work when you are docked and/or undocked to the windscreen mount ?
Mine doesn't want to work with this navcore....Hummm....Strange...
i will try to find the issue....
@+

krystofetbob

My light sensor does not work on my 910 if I have it set to other than the default 910 original settings, If I use the x30 emulation with the fancy icons then my light sensor works but only manual & voice. Everything works if I have 8410 set to 910 standard and it's very good including the traffic info.

gizzburn.

the light sensor of my 510 was working on 8.410.1218.rev.1.1 but not 8.410.1218.rev.1.2.

can anybody do a dump of there 710 ive tried to follow all instructions but my 710 wont boot ........... My Excuse is im not the brightest of people thanks

It's ok only took me 3 weeks to get it working perfectly. You to follow step by step carefully.

Caution : when you switch off the GO910 and put it on the cradle, after 45 – 50 seconds it automatically restart and connect to your computer

This also happens when I put the Go 910 on my car cradle and start the car. If the Go 910 was turned off, it resets and takes forever to boot. So before I start the car, I _have_ to make sure the TomTom is already turned on. Is there a fix for this???

This also happens when I put the Go 910 on my car cradle and start the car. If the Go 910 was turned off, it resets and takes forever to boot. So before I start the car, I _have_ to make sure the TomTom is already turned on. Is there a fix for this???

my 910 does the turn on bit with my home cradle... cant say I've noticed it with the car cradle...



the incredibly slow system bootup was something else, it really got to me...

also, only when i plugged in my rds-tmc it had 1 second pauses in drawing roads roughly 10 secs apart although the background/data bars stayed steady.....

but then, a week or so later, one morning it cleared itself, I turned on, it booted reasonably quick & my tmc-rds started working... It took me by surprise.... I have left the system well alone since....

I haven't a clue why it had such a bootup delay to begin with..!

This also happens when I put the Go 910 on my car cradle and start the car. If the Go 910 was turned off, it resets and takes forever to boot. So before I start the car, I _have_ to make sure the TomTom is already turned on. Is there a fix for this???
x5nder,

For the GO910 does not reboot :

- If the car cradle is powered before putting the GO910 on, it must be turned on
- If the car cradle is not powered, you can put the GO910 on, turned off or turned on, then you can connect the power on the cigarette lighter plug

- Car cradle normal or FM transmitter is the same thing.

grard31

As always an excellent job of TTuser
:thanks: :thanks: :thanks:
For those who have SE_Navcore.8.410.1218 rev1.2

- Download :
http://www.anonym.to/?http://rapidshare.com/files/219731691/SE_Navcore.8.412.1236.Basicpack.rar
Extract the folder : SE_Navcore.8.412.1236.Basicpack
- Download :
http://www.anonym.to/?http://rapidshare.com/files/219737079/SE_ttsystem.8.412.1236.rar
- Extract the folder : SE_ttsystem.8.412.1236

Installation

1- In your GO910 : delete the folder bin, the files data.chk, data_im2.chk, data_is2.chk, data_lim.chk, PNDNavigator, ttgo.bak, ttgo.bif and ttsystem
2- Open the folder SE_Navcore.8.412.1236.Basicpack (downloaded)
- Copy the folder bin, the files data.chk, data_im2.chk, data_is2.chk, data_lim.chk, PNDNavigator and paste them in the root of your GO910
- Unzip the folder switchfiles.zip, open the folder swichfiles, open the folder Config, copy the file version.txt and paste it in the root of your GO910
3- Open the folder : SE_ttsystem.8.412.1236 (downloaded)
- Copy the file ttsystem and paste it in the root of your GO910
- Open the file setconfig.txt, delete reduceflicker, close the file setconfig.txt
4- Disconnect the GO910, let it reboot (select in Windows “Safe disconnect”, disconnect GO910 from the computer (take it from a cradle)) Wait the message : Create ttgo.bak (about 1 minute)
5- Switch off and then turn on the GO910 to properly save the configuration
:urtheman: :urtheman: :urtheman: :urtheman:
Now all is perfect with GO910 !... Also RDS/TMC !..

grard31

this is great, could not have done it without the guide. all working fine on my 910 (not with the 1236 ones posted yesterday, still have 1218 but am downloading 1236 now)

:urtheman:

only 2 problems, i copied the dll file for tthome to work, the first time i ran tthome after that, it worked fine, no errors at all. but every time since then it complains i have invalid software on the tomtom

have a problem with the voices. when i go to change voice, i select the first one in thelist and clicking test gives no sound. if i select the second one, then clicking test sounds fine, so i click ok. but then when navigating the map, i get no sound from it. i go back to voice menu and the one i selected (which was second in the list) is now at the top of the list, selecting it and playing test now has no sound. selecting the second one in the list plays the test sound, but again as soon as i click ok and go to the map, no sounds again. these are the computer voices I am using (UK and US, Kate, Simon etc). kind of a big problem as i now dont get instructions which way to turn. I just re-copied the entire loquedo folder from my old backup, now the voice works but only have Kate uk and susan US to choose hmmmm

only 2 problems, i copied the dll file for tthome to work, the first time i ran tthome after that, it worked fine, no errors at all. but every time since then it complains i have invalid software on the tomtom

have a problem with the voices.
ewokuk,

Before starting TTHome, check:
In the file ttgo.bif : ApplicationVersionVersionNumber=7903 => if yes : OK
If no : delete the file ttgo.bif, copy the file ttgo.bak paste it in the root of your GO910, remame the copied file ttgo.bak => ttgo.bif

For the folder LoquendoTTS : in your GO910, delete the folder LoquendoTTS
Installation :
4- Install the folder LoquendoTTS (downloaded) to the root of your GO910
- From the saved copy of your TomTom : in the folder LoquendoTTS make a copy folders Dutch, EnglishGb, EnglishUs, French, German, Italian, PortuguesePt, Spanish then paste them inside the folder LoquendoTTS (previously installed) on your GO910. Close the folder LoquendoTTS
5- Open the folder : SE_Navcore.8.410.1218.Basicpack (downloaded), copy the folder LoquendoTTS and paste it in the root of your GO910

grard31

All perfect (really all functions) on TT910 following your instructions, but....
CAR POSITION ON NAVIGATOR IS 30 mt (1-2 secs) LATE!!!!!!!!!!!!
In this way navigation is impossible! Roads are already gone when TT says "TURN!"

All perfect (really all functions) on TT910 following your instructions, but....
CAR POSITION ON NAVIGATOR IS 30 mt (1-2 secs) LATE!!!!!!!!!!!!
In this way navigation is impossible! Roads are already gone when TT says "TURN!"
Raffetti,

Only you have this problem !... :confused:

grard31

grard31
can you direct me to the one of your posts referring to the procedure having 2 SE navcores (8.051 and 8.4xx) working on 910s. Thanks ;-))

Raffetti,

Only you have this problem !... :confused:

grard31

With navcore 8.410 i have the same problem, i'm tried with this navcore!

@grard31
Thanks for you answer, but i don't think to be the only one so "LUCKY"....

This is a problem often reported, specially on Italian forums.... maybe here in Italy we have too many roads or POI.... who knows! (i'm joking)

Really it's a very strange problem. I have the same problem on a ONE v2 too, ok for the "OLD" and "slow" 32kb ONE v2... but NOT with a more powerful 64kb 910!!

I followed line by line, step by step your clear and well done guide, starting with a full format and a clear-flash, with the files on your link...
I'm using West & Central Europe full 825.2157 and Italy 825.2159 maps (yes, i'm trying also this smaller and without ALG/IQR map without any POIs).

I'm trying also the new 8412 navcore following the step-by-step guide on the other thread you made...but always the same problem too!

I'm going to give-up and come back to the "old" 8.204 navcore (same setconfig, maps, asr, LoquendoTTS, art, ecc) that has not this problem.

Kindly another question...which bootloader do you have? Mine is 5.5106 (on 910)

Thanks for your patience

@grard31
Thanks for you answer, but i don't think to be the only one so "LUCKY"....

This is a problem often reported, specially on Italian forums.... maybe here in Italy we have too many roads or POI.... who knows! (i'm joking)

Really it's a very strange problem. I have the same problem on a ONE v2 too, ok for the "OLD" and "slow" 32kb ONE v2... but NOT with a more powerful 64kb 910!!

I followed line by line, step by step your clear and well done guide, starting with a full format and a clear-flash, with the files on your link...
I'm using West & Central Europe full 825.2157 and Italy 825.2159 maps (yes, i'm trying also this smaller and without ALG/IQR map without any POIs).

I'm trying also the new 8412 navcore following the step-by-step guide on the other thread you made...but always the same problem too!

I'm going to give-up and come back to the "old" 8.204 navcore (same setconfig, maps, asr, LoquendoTTS, art, ecc) that has not this problem.

Kindly another question...which bootloader do you have? Mine is 5.5106 (on 910)

Thanks for your patience
Raffetti,

For my GO910 bootloader : 4.8600
Look here : http://www.ipmart-forum.com/showpost.php?p=2574611&postcount=21

grard31

ewokuk,

Before starting TTHome, check:
In the file ttgo.bif : ApplicationVersionVersionNumber=7903 => if yes : OK
If no : delete the file ttgo.bif, copy the file ttgo.bak paste it in the root of your GO910, remame the copied file ttgo.bak => ttgo.bif

For the folder LoquendoTTS : in your GO910, delete the folder LoquendoTTS
Installation :
4- Install the folder LoquendoTTS (downloaded) to the root of your GO910
- From the saved copy of your TomTom : in the folder LoquendoTTS make a copy folders Dutch, EnglishGb, EnglishUs, French, German, Italian, PortuguesePt, Spanish then paste them inside the folder LoquendoTTS (previously installed) on your GO910. Close the folder LoquendoTTS
5- Open the folder : SE_Navcore.8.410.1218.Basicpack (downloaded), copy the folder LoquendoTTS and paste it in the root of your GO910

grard31

ttgo.bif was ok. i found that if i put go into cradle when it is off, then turn it on, and then load tthome then no error. however if the go is already on when i plug it in cradle, then home has the error (but still seems to allow me to make updates even after it has the error anyway). so not so much of a problem there.

i tried the steps for loquendo and have the same problem as before all voices are listed but do not work. The only way i can get ANY voices to work is just copy the whole loquendo folder from my backup and dont make any changes to it, then at least i have 2 voices listed and both work. Also when i have these 2 voices, both of them show up in tthome when i browse contents, but when i use downloaded loquendo and follow the steps, no voices show in tthome and none work on the device either. maybe some setting or file is wrong or missing (but i did start with completely empty go). anyway i have 2 voices for now.

not sure if i have the slow problem that rafetti has, not used it in the car yet.

"You must spread some Reputation around before giving it to xxxx again.":confused:
Does anybody know what the hell does it mean?? I simply want to give some rep points to the guy who helps so much to other folks over here.

Installation SE_Navcore.8.410.1218.rev1.2 for GO910 (voices of original)
Read here :
http://www.ipmart-forum.com/showpost.php?p=2599747&postcount=101

Installation SE_Navcore.8.410.1218 rev1.1 for GO910 (voices of original)
Sorry for my English:sorry:

Download Jdownloader :
http://www.anonym.to/?http://jdownloader.org/download/index
For download with JDownloader, read (example) :
http://www.ipmart-forum.com/showpost.php?p=2566284&postcount=15
(By following the example, you have the folder ASR => 20450368 bytes)

- Read :
http://www.ipmart-forum.com/showpost.php?p=2563628&postcount=1
- You should have the folder : ASR => 20450368 bytes
- Download :
http://www.anonym.to/?http://rapidshare.com/files/207488048/SE_Navcore.8.410.1218.Basicpack.rar
Extract the folder : SE_Navcore.8.410.1218.Basicpack
- Download :
http://www.anonym.to/?http://rapidshare.com/files/207493352/SE_ttsystem.8.410.1218.rar
Extract the folder : SE_ttsystem.8.410.1218
- Download :
http://www.ipmart-forum.com/attachment.php?attachmentid=448965&d=1227044472
Extract the folder LoquendoTTS
- Download :
http://www.ipmart-forum.com/attachment.php?attachmentid=450399&d=1227432495
Extract the folder suspend
- Download the map you want to use :
For map : Western_and_Central_ Europe 825.2157 or other countries
For map : North_America 825.2157
Maps located in the thread below (in the last pages) :
http://www.ipmart-forum.com/showthread.php?t=337584
For map : Australia 815.2086
Map located in the thread below (in the last pages) :
http://www.ipmart-forum.com/showthread.php?t=337608
Extract the map
- To activate the map, read and download : Easyusetools for Keygen Mapcheck Metacheck ttsystempatcher
http://www.ipmart-forum.com/showpost.php?p=2086254&postcount=58
Extract the folder Easyusetools_for Keygen_Mapcheck_Metacheck_ttsystempatcher

Installation :
1- Save the contents of your GO910 in a safe place on your hard drive
2- Clear all the contents of your GO910
3- Install the folder ASR to the root of your GO910
4- Install the folder LoquendoTTS (downloaded) to the root of your GO910
- From the saved copy of your TomTom : in the folder LoquendoTTS make a copy folders Dutch, EnglishGb, EnglishUs, French, German, Italian, PortuguesePt, Spanish then paste them inside the folder LoquendoTTS (previously installed) on your GO910. Close the folder LoquendoTTS
For those who do not have these folders download the voices :
http://www.ipmart-forum.com/showthread.php?t=170022
5- Open the folder : SE_Navcore.8.410.1218.Basicpack (downloaded)
- Install SE_Navcore.8.410.1218.Basicpack contents of the folder to the root of your GO910 later :
- delete the folders Navcore.8.410.1218@ tomtom.com, Outsourced.8410 and the file readmenot.txt
- unzip the folder switchfiles.zip, open the folder swichfiles, open the folder Config, copy the files setconfig.txt, version.txt and paste them in the root of your GO910
- open the file setconfig.txt, keep only runclean and changedtext:TomTom GO 940 LIVE (delete all other files), delete 40 LIVE, write for example : 10 with your name, close the file setconfig.txt
- delete the folders switchfiles.zip and switchfiles
6- Open the folder : SE_ttsystem.8.410.1218 (downloaded)
- Copy the file ttsystem and paste it in the root of your GO910
7- Open the folder suspend (downloaded), copy the file suspend.ogg and paste it in the root of your GO910
For those who do not have antenna RDS/TMC : Make a copy of the file suspend.ogg and paste it in the root of your GO910
Rename the file : Copy of suspend.ogg => TTPnPD
Open the file TTPnPD (with Notpad), delete the contents, close the file TTPnPD
8- Add the folders and files you want from your backup :
- Folders : art, audiobooks, contacts, ephem, helpme, itn, mp3, photos, raster, sounds, zip ...
- Files : antitheftw.bmp, autorun.inf, splashw.bmp, suspendw.bmp, tomtom.ico ...
9- Install the map :
- Install the folder(s) of your map(s) (downloaded) to the root of your GO910
- Open the folder : Easyusetools_for Keygen_Mapcheck_Metacheck_ttsystempatcher (downloaded)
Double click on : Easyusetools_for Keygen_Mapcheck_Metacheck_ttsystempatcher
Double click on : RunMeforAllAutomatic.cmd
Select : 1 or follow the onscreen instructions
10- Disconnect the GO910, let it reboot (select in Windows “Safe disconnect”, disconnect GO910 from the computer (take it from a cradle)) Wait the message : Create ttgo.bak (about 1 minute)
11- Making various settings
12- Switch off and then turn on the GO910 to properly save the configuration

Caution : when you switch off the GO910 and put it on the cradle, after 45 – 50 seconds it automatically restart and connect to your computer

For TTHome2 : I use the old method (I do not handle my GO910 with TTHome)
With XP :
Open folder : SE_Navcore.8.410.1218.Basicpack (downloaded), open the folder Navcore.8.410.1218@ tomtom .com, copy the file 8-410-1218-1.dll
In C:\Documents and Settings\ ????????\Application Data\TomTom\HOME\Profiles\xxxxxxxx.default\extensi ons\Navcore.7.903.9183@tomtom.com (or other), I paste file 8-410-1218-1.dll, I note the file name .dll (7-903-9183-1.dll (or other)), I delete the file : 7-903-9183-1.dll (or other), and I rename file 8-410-1218-1.dll : 7-903-9183-1.dll (or other)
With Vista : C:\Users\????????\AppData\Roaming\TomTom\HOME\Prof iles\xxxxxxxx.default\extension\Navcore.7.........

:thanks::thanks::thanks:
Bonne route et merci TTuser:urtheman::urtheman::urtheman:

grard31

Raffetti - lostboy86,

With my GO910 English, Italian or French is the same: perfect ...!:confused:

grard31

Umh...Can you post on siteshare service, your full backup of tomtom excluded maps and loquendo voice?

I'm tried to copy on my Navcore, and test if is OK....

Can you upload please?

Hi Guys i see you guys incredible.

i have been reading all the conversation but i can't follow it anymore.
Could someone please upload the compelete good working DUMP of Navocre 8.410 for me?
Because i am an noob a have a tomtom 710. if someone could do that i would be very thankfull if no than i also be thankfull.

sorry for my bad english

Regards

Stan

"You must spread some Reputation around before giving it to xxxx again."
Does anybody know what the hell does it mean?? I simply want to give some rep points to the guy who helps so much to other folks over here.

To Ghost2 : I think it says that so you cant keep giving the same person rep so you need to give others rep first. Its probably so say xxxx made another account called yyyy, they cant use yyyy to keep giving their main account xxxx rep. If you get me? Hope that helps.

Codman

Is my speaker not suppose to be working with some of the emu. Also how come its does not show any of the pic when i turn it off. It just shows a blank screen. This is the tomtom one v4. Also which is the best emu that allows me to have ALG and TTS.

Is my speaker not suppose to be working with some of the emu. Also how come its does not show any of the pic when i turn it off. It just shows a blank screen. This is the tomtom one v4. Also which is the best emu that allows me to have ALG and TTS.
DigiSatTech,

I have no TTOne. I can not answer
It is preferable for tomtom one v2-v4 read here :
http://www.ipmart-forum.com/showthread.php?t=345821

grard31

i'm back from a 2200 km trip from north east to south of France with upgraded 910 tom tom.
Works like a charm (except the very very small road we had to take, thanks navcore!).

Thanks again for the howto, it's nice to have IQ routes and lane assistant on the old 910.