TPS
23rd March 2004, 10:41
any one have after flash 2300 become dead ?? i got 1 2300 after flash no power on !! any one can help me ??
|
View Full Version : 2300 after flash can't on !! TPS 23rd March 2004, 10:41 any one have after flash 2300 become dead ?? i got 1 2300 after flash no power on !! any one can help me ?? glhs 23rd March 2004, 12:25 did u flash both mcu and ppm ? wat version u flash?? TPS 23rd March 2004, 12:31 i flash both mcu & ppm ! i use RM 5 3.44 !! i flash back RM 4 3.42 still dead .... after flash no test mode no local mode ..... can't on ..... e64y 23rd March 2004, 13:10 Try ufs2 v1.2n,maybe new flash chip. :lol: :lol: :lol: glhs 23rd March 2004, 13:20 u can flash back all the file to phone?? i means the proses was done complete? if not try to flash ppm 1st then flash the both mcu and ppm...... post the result:) alif30 26th March 2004, 13:46 Cable what used to flash 2300? glhs 27th March 2004, 05:42 2300 can be use same as 1100 cable isaackenny 27th March 2004, 06:19 2300 can be use same as 1100 cable this is nothing much more inportant wat TPS want here is solution... I revive by flashing V3.55 RM-5 after few RM-4 flashing with blank LCD .. TPS 28th March 2004, 09:52 same dead ... after flash process ..................fail can't on .... i use 1100 cable !! i aready try ufs2 v1.2m/n griffin ver 1.989/2.05/2.06/2.081/2.082/2.083.... same Srun_Jeff 30th March 2004, 13:09 can i flash 1100 to 2300 jignesh 31st March 2004, 07:35 you mcu and mcu of 2300 and flash ppm only don"t flash mcu it will ok logo3315 20th August 2004, 23:27 same dead ... after flash process ..................fail can't on .... i use 1100 cable !! i aready try ufs2 v1.2m/n griffin ver 1.989/2.05/2.06/2.081/2.082/2.083.... same check your cable! Or buy another the same cable! I think it's cable's problem ccipo 21st August 2004, 17:25 get the new flas file ! v3.60 rm4 ..... ciahendra 26th August 2004, 20:44 Try this solution Use Rm 4 v3.60 flash mcu+ppm and you must flash ppm area and dont flash mcu area use 1100_erase_bb for flash ppm area upload Pm file and phone normal God luck mohd_anan 27th August 2004, 02:39 I have stupid question here but may it helps R u sure it is 2300 ? not 2300a ... ???? Sorry it happend with me one time So make sure it is 2300 And also had u tried erase file ? and u pressed then power a little touch and it start flashing ? If yes Do the flash again and donn't reomve the cable just try the noraml test if yes. Check ur power switch may loose contact Good Luck I like i-phone forum not griffinteam Anan Kuwait mohd_anan 27th August 2004, 02:41 I forgot to say Remove the check box of bluetooth and don't use factory rest too Starware 3rd October 2004, 23:59 hope this help...try this 1.fls rm5 3.580 in ppm area (phone will in test mode) 2.after that fls rm5 3.58qb (phone will in test mode) 3.finally upload Pm file 4. then unlock DONE! good luck saheera 8th October 2004, 03:25 Try to flash with pm with griffin 2.0861 and flash again |