UFS-3ā
15th January 2005, 04:39
From [Only registered and activated users can see links]
|
View Full Version : NEW >>RPL files UFS-3ā 15th January 2005, 04:39 From [Only registered and activated users can see links] orchard-mobile 18th January 2005, 09:25 i hope 2300 rpl is included,.. thx anyway!! i'll try, after i d/l 1st. ;) pinky 18th January 2005, 10:20 orchard mobile can u flash 2600 with nbox ? i get stuck when flashing at "erasing" at 75 and sometimes 79% cable is 1100 and is not loose i noticed that i can only flash by pressing " flash and not start" pinky 18th January 2005, 10:31 i get this on nbox while flashing 2600 1st Boot Ok, DCT4, UPP: 1201 Fl0: 0x01000000-0x013FFFFF,00208828,St M58MR032 Algorithm: u_st_i.fia Algorithm Ok, MSID: 84867EBA69E1F7985A082BDE63 Decoded MSID: 3E4EBAE9-00DBAA5A-A8000000 Encoded FAID: 8C41F49C-2FB62E4E-1A196567 Area: 0x01000000-0x0100FFFF Erased, Time: 0:00 Erasing: 0x01010000-0x013EFFFF ... Erasing Error: 8, at: 0x01300000-0x0131FFFF, Time: 0:46 Process Failed, Repowering Mobile Erasing flash memory stops at 75% can u help ? Please UFS-3ā 18th January 2005, 13:29 i get this on nbox while flashing 2600 1st Boot Ok, DCT4, UPP: 1201 Fl0: 0x01000000-0x013FFFFF,00208828,St M58MR032 Algorithm: u_st_i.fia Algorithm Ok, MSID: 84867EBA69E1F7985A082BDE63 Decoded MSID: 3E4EBAE9-00DBAA5A-A8000000 Encoded FAID: 8C41F49C-2FB62E4E-1A196567 Area: 0x01000000-0x0100FFFF Erased, Time: 0:00 Erasing: 0x01010000-0x013EFFFF ... Erasing Error: 8, at: 0x01300000-0x0131FFFF, Time: 0:46 Process Failed, Repowering Mobile Erasing flash memory stops at 75% can u help ? Please i flash 2600 with ufs-3 + 1100 cable. remember hold tight the cable when flashing till done :P mastermale 22nd January 2005, 03:26 hold ur cable when u r flashing ur mobile to avoid any damage and u can read pm file first from phone from 1 to 250 that is best and u can erase flash and rewrite the new flash to ur phone that will go it that not doing u have to clear the place of cable in ur mobile and try again br , klcheng 25th January 2005, 11:51 where i can get rpl 7610 stboon 25th January 2005, 13:44 where i can get rpl 7610 u can use any off asic 5 rpl....tested..working. orchard-mobile 28th January 2005, 07:30 what about rpl for 2300?? ;) santosh_dts 7th February 2005, 19:14 hold ur cable when u r flashing ur mobile to avoid any damage and u can read pm file first from phone from 1 to 250 that is best and u can erase flash and rewrite the new flash to ur phone that will go it that not doing u have to clear the place of cable in ur mobile and try again br , I have a prob in erasing flash in 1100 the raseing procedure stops at 12% but when i write mcu ppm and pm I have contact service on the phone. the prob is i am using ufs2 and i did not donot have back up of PM . any help please... regards. M A N O J 17th February 2005, 21:17 what about rpl for 2300?? ;) YOU CAN USE ANY ASIC2 RPL FOR 2300 orchard-mobile 22nd February 2005, 08:27 thx, mnoj,.. i'll try ;) winp 10th March 2005, 17:50 hold ur cable when u r flashing ur mobile to avoid any damage and u can read pm file first from phone from 1 to 250 that is best and u can erase flash and rewrite the new flash to ur phone that will go it that not doing u have to clear the place of cable in ur mobile and try again br , I have a prob in erasing flash in 1100 the raseing procedure stops at 12% but when i write mcu ppm and pm I have contact service on the phone. the prob is i am using ufs2 and i did not donot have back up of PM . any help please... regards. u can try this, first unlock the phone then reset the factory default. winp 10th March 2005, 17:52 hold ur cable when u r flashing ur mobile to avoid any damage and u can read pm file first from phone from 1 to 250 that is best and u can erase flash and rewrite the new flash to ur phone that will go it that not doing u have to clear the place of cable in ur mobile and try again br , I have a prob in erasing flash in 1100 the raseing procedure stops at 12% but when i write mcu ppm and pm I have contact service on the phone. the prob is i am using ufs2 and i did not donot have back up of PM . any help please... regards. u can try this, first unlock the phone then reset the factory default. |